Copied from Putty:
Texas Instruments X-Loader 1.4.4ss (Aug 19 2010 - 02:49:27) Beagle xM Rev A Reading boot sector Loading u-boot.bin from mmc U-Boot 2010.03-dirty (Aug 20 2010 - 20:50:46) OMAP3630/3730-GP ES2.0, CPU-OPP2, L3-165MHz, OMAP3 Beagle board + LPDDR/NAND I2C: ready DRAM: 512 MB NAND: 0 MiB *** Warning - bad CRC or NAND, using default environment In: serial Out: serial Err: serial Probing for expansion boards, if none are connected you'll see a harmless I2C error. No EEPROM on expansion board Beagle xM Rev A Die ID #440000019ff80000015eeaa102011004 Hit any key to stop autoboot: 3 2 1 0 mmc1 is available The user button is currently PRESSED. reading user.scr 755 bytes read Running bootscript from mmc ... ## Executing script at 80200000 mmc1 is available reading ramdisk.gz 19960110 bytes read reading uImage 3190568 bytes read Booting from ramdisk ... ## Booting kernel from Legacy Image at 80200000 ... Image Name: Angstrom/2.6.32/beagleboard Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3190504 Bytes = 3 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux................................................................................................................................................................................................................ done, booting the kernel. [ 0.000000] Linux version 2.6.32 (ubuntu@ip-10-204-115-71) (gcc version 4.3.3 (GCC) ) #3 PREEMPT Wed Aug 18 15:53:03 UTC 2010 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7f [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache [ 0.000000] Machine: OMAP3 Beagle Board [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] OMAP3630/DM3730 ES1.0 (l2cache iva sgx neon isp 192mhz_clk ) [ 0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000 [ 0.000000] Reserving 16777216 bytes SDRAM for VRAM [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 117760 [ 0.000000] Kernel command line: console=tty0 console=ttyS2,115200n8 mem=80M@0x80000000 mem=384M@0x88000000 mpurate=1000 buddy=none camera=lbcm3m1 vram=16M omapfb.vram=0:8M,1:4M,2:4M omapfb.mode=dvi:1024x768MR-16@60 omapdss.def_disp=dvi root=/dev/ram0 rw ramdisk_size=131072 initrd=0x88000000,128M rootfstype=ext2 [ 0.000000] Beagle expansionboard: none [ 0.000000] Beagle cameraboard: lbcm3m1 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 80MB 384MB = 464MB total [ 0.000000] Memory: 316288KB available (5880K code, 671K data, 204K init, 0K highmem) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:402 [ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/332/600 MHz [ 0.000000] Reprogramming SDRC clock to 332000000 Hz [ 0.000000] GPMC revision 5.0 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts [ 0.000000] Total of 96 interrupts on 1 active controller [ 0.000000] OMAP GPIO hardware version 2.5 [ 0.000000] OMAP clockevent source: GPTIMER12 at 32768 Hz [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] console [tty0] enabled [ 0.000000] Calibrating delay loop... 498.87 BogoMIPS (lpj=1945600) [ 0.000000] Mount-cache hash table entries: 512 [ 0.000000] CPU: Testing write buffer coherency: ok [ 0.000000] tmpfs: No value for mount option 'mode' [ 0.000000] devtmpfs: initialized [ 0.000000] regulator: core version 0.5 [ 0.000000] NET: Registered protocol family 16 [ 0.000000] Beagle cameraboard: registering i2c2 bus for lbcm3m1 [ 0.000000] Found NAND on CS0 [ 0.000000] Registering NAND on CS0 [ 0.000000] Unable to get DVI reset GPIO [ 0.000000] omap_init_mbox: platform not supported [ 0.000000] Target VDD1 OPP = 4, VDD2 OPP = 2 [ 66.129547] OMAP DMA hardware revision 5.0 [ 66.135864] bio: create slab <bio-0> at 0 [ 66.137145] SCSI subsystem initialized [ 66.138519] usbcore: registered new interface driver usbfs [ 66.138671] usbcore: registered new interface driver hub [ 66.138854] usbcore: registered new device driver usb [ 66.139251] i2c_omap i2c_omap.1: bus 1 rev4.0 at 2600 kHz [ 66.141937] twl4030: PIH (irq 7) chaining IRQs 368..375 [ 66.141998] twl4030: power (irq 373) chaining IRQs 376..383 [ 66.142303] twl4030: gpio (irq 368) chaining IRQs 384..401 [ 66.144012] regulator: VUSB1V5: 1500 mV normal standby [ 66.144256] regulator: VUSB1V8: 1800 mV normal standby [ 66.144500] regulator: VUSB3V1: 3100 mV normal standby [ 66.148132] twl4030_usb twl4030_usb: Initialized TWL4030 USB module [ 66.148559] regulator: VMMC1: 1850 <--> 3150 mV normal standby [ 66.148834] regulator: VDAC: 1800 mV normal standby [ 66.149078] regulator: VPLL2: 1800 mV normal standby [ 66.149322] regulator: VSIM: 1800 <--> 3000 mV normal standby [ 66.149688] regulator: VAUX3: 1800 mV normal standby [ 66.150054] regulator: VAUX4: 1800 mV normal standby [ 66.150238] i2c_omap i2c_omap.2: bus 2 rev4.0 at 400 kHz [ 66.157714] i2c_omap i2c_omap.3: bus 3 rev4.0 at 100 kHz [ 66.158935] Switching to clocksource 32k_counter [ 66.167877] musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0 [ 66.168212] musb_hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92 [ 66.168243] musb_hdrc musb_hdrc: MUSB HDRC host driver [ 66.168395] musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1 [ 66.168548] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 66.168609] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 66.168640] usb usb1: Product: MUSB HDRC host driver [ 66.168670] usb usb1: Manufacturer: Linux 2.6.32 musb-hcd [ 66.168731] usb usb1: SerialNumber: musb_hdrc [ 66.169372] hub 1-0:1.0: USB hub found [ 66.169433] hub 1-0:1.0: 1 port detected [ 66.170501] NET: Registered protocol family 2 [ 66.170745] IP route cache hash table entries: 4096 (order: 2, 16384 bytes) [ 66.171325] TCP established hash table entries: 16384 (order: 5, 131072 bytes) [ 66.171722] TCP bind hash table entries: 16384 (order: 4, 65536 bytes) [ 66.171966] TCP: Hash tables configured (established 16384 bind 16384) [ 66.171997] TCP reno registered [ 66.172058] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 66.172088] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 66.172363] NET: Registered protocol family 1 [ 66.172790] RPC: Registered udp transport module. [ 66.172851] RPC: Registered tcp transport module. [ 66.172882] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 66.173187] Trying to unpack rootfs image as initramfs... [ 66.176055] rootfs image is not initramfs (no cpio magic); looks like an initrd [ 66.741271] Freeing initrd memory: 131072K [ 66.742065] omap-iommu omap-iommu.0: isp registered [ 66.743927] VFS: Disk quotas dquot_6.5.2 [ 66.744049] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 66.745239] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 66.746124] JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 66.746948] msgmni has been set to 874 [ 66.750671] alg: No test for stdrng (krng) [ 66.750976] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) [ 66.751037] io scheduler noop registered [ 66.751068] io scheduler deadline registered [ 66.751220] io scheduler cfq registered (default) [ 66.807617] OMAP DSS rev 2.0 [ 66.807678] OMAP DISPC rev 3.0 [ 66.807769] OMAP VENC rev 2 [ 66.808013] OMAP DSI rev 1.0 [ 67.144470] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 67.162353] serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654 [ 67.179565] serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654 [ 67.196746] serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654 [ 67.796722] console [ttyS2] enabled [ 67.806976] brd: module loaded [ 67.813385] loop: module loaded [ 67.817687] omap2-nand driver initializing [ 67.822113] No NAND device found!!! [ 67.825836] No NAND device found!!! [ 67.830352] usbcore: registered new interface driver catc [ 67.835876] catc: v2.8:CATC EL1210A NetMate USB Ethernet driver [ 67.841949] usbcore: registered new interface driver kaweth [ 67.847625] pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver [ 67.855285] usbcore: registered new interface driver pegasus [ 67.860992] rtl8150: v0.6.2 (2004/08/27):rtl8150 based usb-ethernet driver [ 67.868011] usbcore: registered new interface driver rtl8150 [ 67.873840] usbcore: registered new interface driver asix [ 67.879394] usbcore: registered new interface driver cdc_ether [ 67.885345] usbcore: registered new interface driver dm9601 [ 67.891113] usbcore: registered new interface driver smsc95xx [ 67.897003] usbcore: registered new interface driver gl620a [ 67.902740] usbcore: registered new interface driver net1080 [ 67.908538] usbcore: registered new interface driver plusb [ 67.914184] usbcore: registered new interface driver rndis_host [ 67.920257] usbcore: registered new interface driver cdc_subset [ 67.926330] usbcore: registered new interface driver zaurus [ 67.932037] usbcore: registered new interface driver MOSCHIP usb-ethernet driver [ 67.940124] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 67.947021] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller [ 67.953094] ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 2 [ 67.960754] ehci-omap ehci-omap.0: irq 77, io mem 0x48064800 [ 67.979400] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00 [ 67.985321] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 67.992218] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 67.999511] usb usb2: Product: OMAP-EHCI Host Controller [ 68.004913] usb usb2: Manufacturer: Linux 2.6.32 ehci_hcd [ 68.010375] usb usb2: SerialNumber: ehci-omap.0 [ 68.015655] hub 2-0:1.0: USB hub found [ 68.019531] hub 2-0:1.0: 3 ports detected [ 68.049804] Initializing USB Mass Storage driver... [ 68.054901] usbcore: registered new interface driver usb-storage [ 68.061004] USB Mass Storage support registered. [ 68.066040] mice: PS/2 mouse device common for all mice [ 68.071716] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 68.079589] input: twl4030_pwrbutton as /devices/platform/i2c_omap.1/i2c-1/1-0049/twl4030_pwrbutton/input/input1 [ 68.090362] i2c /dev entries driver [ 68.094451] Linux video capture interface: v2.00 [ 68.099456] omap-iommu omap-iommu.0: isp: version 1.1 [ 68.105895] vpfe_init [ 68.108764] OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec [ 68.221923] mmci-omap-hs mmci-omap-hs.1: err -16 configuring card detect [ 68.229003] Registered led device: beagleboard::usr0 [ 68.234191] Registered led device: beagleboard::usr1 [ 68.240814] Registered led device: beagleboard::pmu_stat [ 68.247924] usbcore: registered new interface driver usbhid [ 68.253601] usbhid: USB HID core driver [ 68.257659] Advanced Linux Sound Architecture Driver Version 1.0.21. [ 68.264587] usbcore: registered new interface driver snd-usb-audio [ 68.330627] No device for DAI omap-mcbsp-dai-0 [ 68.335174] No device for DAI omap-mcbsp-dai-1 [ 68.339691] No device for DAI omap-mcbsp-dai-2 [ 68.344177] No device for DAI omap-mcbsp-dai-3 [ 68.348693] No device for DAI omap-mcbsp-dai-4 [ 68.353179] OMAP3 Beagle SoC init [ 68.357360] asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok [ 68.368774] ALSA device list: [ 68.371856] #0: omap3beagle (twl4030) [ 68.375823] oprofile: using arm/armv7 [ 68.379821] TCP cubic registered [ 68.383087] NET: Registered protocol family 17 [ 68.387664] NET: Registered protocol family 15 [ 68.392211] lib80211: common routines for IEEE802.11 drivers [ 68.397979] ThumbEE CPU extension supported. [ 68.402343] Power Management for TI OMAP3. [ 68.406860] usb 2-2: new high speed USB device using ehci-omap and address 2 [ 68.414978] Unable to set L3 frequency (400000000) [ 68.419921] Switched to new clocking rate (Crystal/Core/MPU): 26.0/332/1000 MHz [ 68.427337] IVA2 clocking rate: 800 MHz [ 68.596557] SmartReflex driver initialized [ 68.600799] omap3beaglelmb: Driver registration complete [ 68.611511] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 68.619812] registered taskstats version 1 [ 68.624664] fbcvt: 1024x768@60: CVT Name - .786M3-R [ 68.722015] usb 2-2: New USB device found, idVendor=0424, idProduct=9514 [ 68.728790] usb 2-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 68.743133] Console: switching to colour frame buffer device 128x48 [ 68.756652] hub 2-2:1.0: USB hub found [ 68.762817] hub 2-2:1.0: 5 ports detected [ 68.766967] regulator_init_complete: incomplete constraints, leaving VAUX4 on [ 68.774353] regulator_init_complete: incomplete constraints, leaving VAUX3 on [ 68.782165] regulator_init_complete: incomplete constraints, leaving VDAC on [ 68.789550] omap_vout omap_vout: probed for an unknown device [ 68.796508] RAMDISK: gzip image found at block 0 [ 68.932678] mmc0: new high speed SDHC card at address 1234 [ 68.948272] mmcblk0: mmc0:1234 SA04G 3.67 GiB [ 68.953125] mmcblk0: p1 p2 [ 69.081817] usb 2-2.1: new high speed USB device using ehci-omap and address 3 [ 69.215911] usb 2-2.1: New USB device found, idVendor=0424, idProduct=ec00 [ 69.229614] usb 2-2.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 69.248626] smsc95xx v1.0.4 [ 69.343872] usb0: register 'smsc95xx' at usb-ehci-omap.0-2.1, smsc95xx USB 2.0 Ethernet, 22:44:84:e2:ca:f9 [ 71.429687] VFS: Mounted root (ext2 filesystem) on device 1:0. [ 71.438354] devtmpfs: mounted [ 71.443817] Freeing init memory: 204K INIT: version 2.86 booting Please wait: booting... Starting udev [ 73.628021] FAT: bogus number of reserved sectors [ 73.635284] VFS: Can't find a valid FAT filesystem on dev mmcblk0. [ 74.051391] FAT: bogus number of reserved sectors [ 74.058776] VFS: Can't find a valid FAT filesystem on dev mmcblk0p2. Remounting root file system... Caching udev devnodes Populating dev cache Configuring network interfaces... ifconfig: SIOCGIFFLAGS: No such device udhcpc (v1.13.2) started Sending discover... Sending discover... Sending discover... No lease, forking to background done. Setting up IP spoofing protection: rp_filter. hwclock: can't open '/dev/misc/rtc': No such file or directory Fri Aug 20 20:54:00 UTC 2010 hwclock: can't open '/dev/misc/rtc': No such file or directory Configuring update-modules. Configuring ti-dsplink-module. Configuring ti-lpm-module. Configuring util-linux-ng. update-alternatives: Linking //bin/dmesg to dmesg.util-linux-ng update-alternatives: Linking //bin/kill to kill.util-linux-ng update-alternatives: Linking //bin/more to more.util-linux-ng update-alternatives: Linking //sbin/mkswap to mkswap.util-linux-ng update-alternatives: Linking //sbin/pivot_root to pivot_root.util-linux-ng update-alternatives: Linking //sbin/sln to sln.util-linux-ng update-alternatives: Linking //sbin/mkfs.minix to mkfs.minix.util-linux-ng update-alternatives: Linking //sbin/fsck.minix to fsck.minix.util-linux-ng update-alternatives: Linking //usr/bin/hexdump to hexdump.util-linux-ng update-alternatives: Linking //usr/bin/last to last.sysvinit update-alternatives: Linking //usr/bin/logger to logger.util-linux-ng update-alternatives: Linking //usr/bin/mesg to mesg.sysvinit update-alternatives: Linking //usr/bin/renice to renice.util-linux-ng update-alternatives: Linking //usr/bin/wall to wall.sysvinit update-alternatives: Linking //usr/bin/chfn to chfn.util-linux-ng update-alternatives: Linking //usr/bin/newgrp to newgrp.util-linux-ng update-alternatives: Linking //usr/bin/chsh to chsh.util-linux-ng update-alternatives: Linking //bin/login to login.util-linux-ng update-alternatives: Error: not linking //sbin/vipw to vipw.util-linux-ng since //sbin/vipw exists and is not a link update-alternatives: Linking //sbin/vigr to vigr.util-linux-ng update-alternatives: Linking //usr/bin/reset to reset.util-linux-ng update-alternatives: Linking //usr/bin/setsid to setsid.util-linux-ng update-alternatives: Linking //usr/bin/chrt to chrt.util-linux-ng update-alternatives: Linking //sbin/hwclock to ../bin/busybox update-alternatives: Linking //sbin/shutdown to shutdown.sysvinit update-alternatives: Linking //sbin/reboot to reboot.sysvinit update-alternatives: Linking //sbin/halt to halt.sysvinit INIT: Entering runlevel: 5 Creating Dropbear SSH server RSA host key. Will output 1024 bit rsa secret key to '/etc/dropbear/dropbear_rsa_host_key' Generating key, this may take a while... Public key portion is: ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAAAgwCOCoZMwVprkTNHaNnmANYJZ7pwtScgwtL1yBqkXHuH3pbMhBgznK6MDYPMTeRXJRjJHtBvyfQu35Yepn3U0QzwkccAm2Kd++fo265yAe7LQTcI1nN1O+0jWArse401bU+I27Unb4RP2QnOanScVGiPxFhHgM9fqFb6IXhimEtLS+Pn root@beagleboard Fingerprint: md5 c3:d9:32:e3:94:2c:c1:43:66:9f:8e:ab:d1:28:12:a9 Starting Dropbear SSH server: dropbear. Starting syslogd/klogd: done .-------. | | .-. | | |-----.-----.-----.| | .----..-----.-----. | | | __ | ---'| '--.| .-'| | | | | | | | |--- || --'| | | ' | | | | '---'---'--'--'--. |-----''----''--' '-----'-'-'-' -' | '---' The Angstrom Distribution beagleboard ttyS2 Angstrom 2010.7-test-20100820 beagleboard ttyS2 beagleboard login: root root@beagleboard:~#